Automated Room Light - Revision history

87.6.8.217: /* Set Up */

2024-10-06T14:46:41Z

Set Up

← Older revision		Revision as of 14:46, 6 October 2024
Line 13:		Line 13:
	Set up each room with its own [[Power Controller]]. Optional*		Set up each room with its own [[Power Controller]]. Optional*
	*While holding the [[Sensors\|Kit (Sensors)]], scroll till you can place [[Occupancy Sensor]].		*While holding the [[Sensors\|Kit (Sensors)]], scroll till you can place [[Occupancy Sensor]].
	*While holding the [[Kit (Logic I/O)]], scroll till you can place a [[Logic ~~Writer~~]].		*While holding the [[Kit (Logic I/O)]], scroll till you can place a [[Logic Reader]].
	*While holding the [[Kit (Logic I/O)]], scroll till you can place a [[Batch Writer]].		*While holding the [[Kit (Logic I/O)]], scroll till you can place a [[Batch Writer]].
	*Connect all [[Cable Coils]] to all the ports on each of the logic, sensor, and light.		*Connect all [[Cable Coils]] to all the ports on each of the logic, sensor, and light.

Azdle: /* Assigning Signals */

2024-07-28T16:55:09Z

Assigning Signals

← Older revision		Revision as of 16:55, 28 July 2024
Line 21:		Line 21:


	[[File:~~IO wall logic Settings~~.jpg\|~~defult~~\|~~left\|Logic with Labels~~]]		[[File:Simple automatic light.jpg\|thumb\|center]]

2601:603:703:16B0:E8D8:6CB:B21A:17F5: /* Set Up */

2024-07-28T16:50:23Z

Set Up

← Older revision		Revision as of 16:50, 28 July 2024
Line 11:		Line 11:

	== Set Up ==		== Set Up ==
	*~~This is not a must, set~~ up each room with its own [[Power Controller]].		Set up each room with its own [[Power Controller]]. Optional*
	*While holding the [[Sensors\|Kit (Sensors)]], scroll till you can place [[Occupancy Sensor]].		*While holding the [[Sensors\|Kit (Sensors)]], scroll till you can place [[Occupancy Sensor]].
	*Place your [[Kit (Logic Memory)]].
	*While holding the [[Kit (Logic Processor)]], scroll till you can place [[Compare Unit]].
	*While holding the [[Kit (Logic I/O)]], scroll till you can place a [[Logic Writer]].		*While holding the [[Kit (Logic I/O)]], scroll till you can place a [[Logic Writer]].
	*While holding the [[Kit (Logic I/O)]], scroll till you can place a [[Batch Writer]].		*While holding the [[Kit (Logic I/O)]], scroll till you can place a [[Batch Writer]].
	*Connect all [[Cable Coils]] to all the ports on each of the logic.		*Connect all [[Cable Coils]] to all the ports on each of the logic, sensor, and light.

	== Assigning Signals ==		== Assigning Signals ==

2601:603:703:16B0:E8D8:6CB:B21A:17F5: /* What you will need */

2024-07-28T16:48:02Z

What you will need

← Older revision		Revision as of 16:48, 28 July 2024
Line 9:		Line 9:
	*[[Sensors\|Kit (Sensors)]] X1		*[[Sensors\|Kit (Sensors)]] X1
	*[[Kit (Logic I/O)]] X2		*[[Kit (Logic I/O)]] X2
	*[[Kit (Logic Memory)]] X1
	*[[Kit (Logic Processor)]] X1

	== Set Up ==		== Set Up ==

Azdle: Created page with "== Definition == This is an automated light system that uses an occupancy sensor to turn lights on and off in a room. == Disclaimer == The room needs to be closed off by a d..."

2024-07-14T18:15:33Z

Created page with "== Definition == This is an automated light system that uses an occupancy sensor to turn lights on and off in a room. == Disclaimer == The room needs to be closed off by a d..."

New page

== Definition ==

This is an automated light system that uses an occupancy sensor to turn lights on and off in a room.

== Disclaimer ==
The room needs to be closed off by a door/hatch for the logic to work and all the walls have to be put into place with at least one sheet put into them before this will work.

== What you will need==
*[[Sensors|Kit (Sensors)]] X1
*[[Kit (Logic I/O)]] X2
*[[Kit (Logic Memory)]] X1
*[[Kit (Logic Processor)]] X1

== Set Up ==
*This is not a must, set up each room with its own [[Power Controller]].
*While holding the [[Sensors|Kit (Sensors)]], scroll till you can place [[Occupancy Sensor]].
*Place your [[Kit (Logic Memory)]].
*While holding the [[Kit (Logic Processor)]], scroll till you can place [[Compare Unit]].
*While holding the [[Kit (Logic I/O)]], scroll till you can place a [[Logic Writer]].
*While holding the [[Kit (Logic I/O)]], scroll till you can place a [[Batch Writer]].
*Connect all [[Cable Coils]] to all the ports on each of the logic.

== Assigning Signals ==

[[File:IO wall logic Settings.jpg|defult|left|Logic with Labels]]