Suit Storage

Kit (Suit Storage)

Recipe
Created With	Hydraulic Pipe Bender, Fabricator
Cost	15g Iron, 5g Copper, 5g Silver

Suit Storage

Operation
Construction
Placed with	Kit (Suit Storage)
Placed on	Free (forced right side up)
Stage 1
Deconstruction
Deconstructed with	Hand Drill
Item received	Kit (Suit Storage)

Description

Used to store the EVA Suit, Helmet, Headlamp, and Spacepack. If the suit storage is powered and has pipes connected with Oxygen [O2] or Propellant [N2], it will recharge the batteries (1kW charge rate + 50w Standby\Operating cost) and equalize the Air Tank Canister and the Propellant Tank Canister with the pipesystem inside it. The wastetank will be pumped out to the pipe connected to the waste outlet.
All pipes must be connected or it will error out, it will still charge the battery and mix gases with connected pipes in error mode. It does not have internal pressure regulators, Must be connected to regulated O2/N2 supply.

Caution: the only pumping operations performed by the Suit Storage itself are emptying the waste tank into the waste pipe and draining liquids from the input and jetpack tanks. It does both instantaneously on insertion and may damage piping.

Inputs/Outputs:

• Front Input is O2,
  
• Back Bottom Input is N2, and
  
• Top Back Output is Waste

Programmable control

While the Suit Storage exposes the pressure values through its data parameters and slot variables, it provides no way to distinguish whether the breathable or propellant canister inside a suit piece is empty or simply absent, the readings will show "0" in either case.

Additionally, there is no way to detect if a suit piece has a canister that can hold higher pressure, such as the Gas Canister (Smart).

Data Network Properties

These are all Data Network properties of this device.

Data Parameters

These are all parameters, that can be written to with a Logic Writer or a Batch Writer. The outputs are listed in the order a Logic Writer's "VAR" setting cycles through them.

Parameter Name	Data Type	Description
Setting	Integer	Inherited from pump class.
On	Boolean	Turns the device on, when set >= 1. Turns it off, when set to <1.

Data Outputs

These are all parameters, that can be read with a Logic Reader. The outputs are listed in the order a Logic Reader's "VAR" setting cycles through them.

Output Name	Data Type	Description
Power	Boolean	Returns whether the device is turned on and receives power. (0 for no, 1 for yes).
Error	Boolean	Returns whether the device is flashing an error. (0 for no, 1 for yes).
Setting	Integer	Inherited from pump class.
Maximum	Integer	Inherited from pump class.
Ratio	Integer	Inherited from pump class.
On	Boolean	Returns whether the device is turned on. (0 for no, 1 for yes)
RequiredPower	Integer	Returns the current amount of power, required by the device, in watts.

Data Slots

These are all parameters, that can be read with a Slots Reader. The outputs are listed in the order a Slots Reader's "VAR" setting cycles through them.

Number	Name	Description
0	Helmet
1	Suit
2	Back

Name	Data Type	Description
All
Occupied	Boolean	Returns whether the slot occupied. (0 for no, 1 for yes).
OccupantHash	Integer	Returns ItemHash of item in slot.
MaxQuantity	Integer	Size of stack.
Damage	Integer	Item durability in percent.
Class	Integer	Item class ID.
Quantity	Integer	Size of stack.
PrefabHash	Integer	Returns ItemHash of item in slot.
Suit
ChargeRatio	Integer	Percent charge in 0-1.
Charge	Integer	Charge in Joules.
PressureWaste	Integer	Pressure of wastetank.
PressureAir	Integer	Pressure of airtank.
Back
Pressure	Integer	Pressure of Jettank.